Intensification of Red-G dye degradation used in the dyeing of alpaca wool by advanced oxidation processes assisted by hydrodynamic cavitation.

Red-G dye is one of the main dyes used in the textile industry to dye alpaca wool. Therefore, considering the large volume of processed wool in Perú, the development of efficient technologies for its removal is a present scientific issue. In this study, an integrated system based on hydrodynamic cavitation (HC) and photo-Fenton process was evaluated to remove the Red-G dye. Using a hybrid cavitation device (venturi + orifice plate), the effect of pH was evaluated, achieving 21 % of removal at pH 2 which was more than 80 % higher compared to pH 4 and 6. The effect of temperature was also evaluated in HC-system at pH 2, where percentage of dye degradation increased at lower temperatures (around 20 °C). Then, 50.7 % of dye was removed under optimized condition of HC-assisted Fenton process (FeSO4:H2O2 of 1:30), that value was improved strongly by UV-light incorporation in the HC-system, increasing to 99 % removal efficiency with respect to HC-assisted Fenton process and reducing the time to 15 min. Finally, the developed cavitation device in combination with photo-Fenton process removed efficiently the dye and thus could be considered an interesting option for application to real wastewater.

Alternative methods for cleaning membranes in water and wastewater treatment.

Membrane fouling is caused by foulant deposition or adsorption through physical or chemical interactions on the membrane surface, causing the reduction of flux through the membrane. The main drawbacks of chemical agents used for cleaning are cost, damage caused on the membrane, and waste stream making the process unattractive. Alternative, methods such as ultrasound, enzymatic process, and osmotic backwashing were explored for membrane cleaning. Among all mentioned methods, micronanobubbles have been reported as a promising and emergent method for membrane surface cleaning; unfortunately, the information is limited, but preliminary studies have shown it as an efficient, cheap, and environmentally friendly technique. Other methods like electrically and vibratory-enhanced membrane cleaning also could be interesting but currently are unexplored and information is limited. PRACTITIONER POINTS: Chemical cleaning is an efficient option; however, from an environmental point of view, it is not attractive, and high concentrations could cause damage to the membrane. Micronanobubbles are an emergent and suitable technology for membrane and surface cleaning. Membrane modification and functionalization avoid membrane fast fouling, and the cleaning process is easier, but the manufacture cost could be expensive.

Surfactants in biorefineries: Role, challenges & perspectives.

The use of lignocellulosic biomass (LCB) as feedstock has received increasing attention as an alternative to fossil-based refineries. Initial steps such as pretreatment and enzymatic hydrolysis are essential to breakdown the complex structure of LCB to make the sugar molecules available to obtain bioproducts by fermentation. However, these steps increase the cost of the bioproduct and often reduces its competitiveness against synthetic products. Currently, the use of surfactants has shown considerable potential to enhance lignocellulosic biomass processing. This review addresses the main mechanisms and role of surfactants as key molecules in various steps of biorefinery processes, viz., increasing the removal of lignin and hemicellulose during the pretreatments, increasing enzymatic stability and enhancing the accessibility of enzymes to the polymeric fractions, and improving the downstream process during fermentation. Further, technical advances, challenges in application of surfactants, and future perspectives to augment the production of several high value-added bioproducts have been discussed.

Emerging contaminants, SARS-COV-2 and wastewater treatment plants, new challenges to confront: A short review.

The current pandemic caused by SARS-CoV-2 has put public health at risk, being wastewater-based epidemiology (WBE) a potential tool in the detection, prevention, and treatment of present and possible future outbreaks, since this virus enters wastewater through various sources such as feces, vomit, and sputum. Thus, advanced technologies such as advanced oxidation processes (AOP), membrane technology (MT) are identified through a systematic literature review as an alternative option for the destruction and removal of emerging contaminants (drugs and personal care products) released mainly by infected patients. The objectives of this review are to know the implications that the new COVID-19 outbreak is generating and will generate in water compartments, as well as the new challenges faced by wastewater treatment plants due to the change in a load of contaminants and the solutions proposed based on the aforementioned technologies to be applied to preserve public health and the environment.

Acid precipitation followed by microalgae (Chlorella vulgaris) cultivation as a new approach for poultry slaughterhouse wastewater treatment.

Poultry slaughterhouse wastewater (PSW) contains high organic matter and nutrients requiring thus a special treatment before its final disposal. In this work, acid precipitation (H2SO4) followed by microalgae "Chlorella vulgaris" cultivation both in batch and continuous processes was studied as an alternative method for PSW treatment. By reducing the pH value of PSW from 6 to 7 to 4, about 80% of the total chemical oxygen demand (CODT) was removed as sludge. In the supernatant, the COD residual was efficiently removed (83%) by microalgae in the batch process, using an internal-loop concentric tube photobioreactor (4.5 L). Moreover, in continuous process, after 89 h, the COD value resulted lower than 200 mg L-1 and 1.2 g L-1 of microalgae in the output line. The proposed PSW treatment method is promising from economic and environmental viewpoints, since the microalgal biomass can be valued in a biorefinery context.

Hydrodynamic cavitation-assisted continuous pre-treatment of sugarcane bagasse for ethanol production: Effects of geometric parameters of the cavitation device.

For biotechnological conversion of lignocellulosic biomass, a pre-treatment step is required before enzymatic hydrolysis of carbohydrate fractions of the material, which is required to produce fermentable sugars for generation of ethanol or other products in a biorefinery. The most of the reported pre-treatment technologies are in batch operation mode, presenting some disadvantages as dead times in the process. In this context, hydrodynamic cavitation (HC)-assisted alkaline hydrogen peroxide (AHP) pre-treatment in continuous process was proposed for pre-treatment of sugarcane bagasse (SCB). The system was designed with a main reactor containing two devices to generate cavitation by passing liquid medium through orifice plates. For SCB pretreated in continuous process, 52.79, 34.31, 22.13 and 15.81 g of total reducing sugars (TRS) per 100 g of SCB were released in samples pretreated using orifice plates with a number of holes of 24 (d = 0.45 mm), 16 (d = 0.65 mm), 12 (d = 0.8 mm) and 8 (d = 1 mm), respectively. Computational Fluid Dynamics (CFD) tools showed that 0.94 of vapor phase volume fraction and 0.19 of cavitation number were achieved at 31 m/s of throat velocity and upstream pressure of 350,000 Pa. By using pretreated SCB, 28.44 g of ethanol/L (84.31% of yield respect to theoretical value) was produced by immobilized Scheffersomyces stipitis NRRL-Y7124 in a simultaneous hydrolysis and fermentation process at high solid loading (16% S/L). Thus, HC-assisted process was proved as a promising technology for valorization of lignocellulosic biomass.

Overcoming challenges in lignocellulosic biomass pretreatment for second-generation (2G) sugar production: emerging role of nano, biotechnological and promising approaches.

Production of green chemicals and biofuels in biorefineries is the potential alternative for petrochemicals and gasoline in transitioning of petro-economy into bioeconomy. However, an efficient biomass pretreatment process must be considered for the successful deployment of biorefineries, mainly for use of lignocellulosic raw materials. However, biomass recalcitrance plays a key role in its saccharification to obtain considerable sugar which can be converted into ethanol or other biochemicals. In the last few decades, several pretreatment methods have been developed, but their feasibility at large-scale operations remains as a persistent bottleneck in biorefineries. Pretreatment methods such as hydrodynamic cavitation, ionic liquids, and supercritical fluids have shown promising results in terms of either lignin or hemicellulose removal, thus making remaining carbohydrate fraction amenable to the enzymatic hydrolysis for clean and high amount of fermentable sugar production. However, their techno-economic feasibility at industrial scale has not been yet studied in detail. Besides, nanotechnological-based technologies could play an important role in the economically viable 2G sugar production in future. Considering these facts, in the present review, we have discussed the existing promising pretreatment methods for lignocellulosic biomass and their challenges, besides this strategic role of nano and biotechnological approaches towards the viability and sustainability of biorefineries is also discussed.

Low-pressure homogenization of tomato juice using hydrodynamic cavitation technology: Effects on physical properties and stability of bioactive compounds.

Hydrodynamic cavitation (HC) technology, offers benefits in many processes, specifically due to its low operational cost and simple configuration. In the present work, physical properties, microbial quality and stability of bioactive compounds of HC-treated tomato juice were evaluated considering different processing conditions. Significant effects of the induced cavitation such as a reduction in particle size and an increase in the apparent viscosity were observed in the HC-treated samples. Moreover, the HC-treated tomato juice showed higher stability without sedimentation for 14 days compared to a sedimentation index of 68% observed in samples before treatment and control experiment. Lycopene and phenolic contents in tomato juice were not altered even after HC-treatment. Finally, the microbiological quality was also improved, mainly for the samples treated above 55 °C. Therefore, this technology can be envisaged as a promising strategy for food processing to enhancing desirable properties in juices.

A new approach for bioethanol production from sugarcane bagasse using hydrodynamic cavitation assisted-pretreatment and column reactors.

Hydrodynamic cavitation (HC) was adopted to assist alkaline-hydrogen peroxide pretreatment of sugarcane bagasse (SCB). In the following condition: 0.29 M of NaOH, 0.78% (v/v) of H2O2, 9.95 min of process time and 3 bar of inlet pressure, 95.4% of digestibility of cellulosic fraction was achieved. To take the best use of the pretreated biomass, the overall process was intensified by way of employing a packed bed flow-through column reactor and thus enabling to handle a high solid loading of 20%, thereby leading to cellulose and hemicellulose conversions to 74.7% and 75%, respectively. In the fermentation step, a bubble column reactor was introduced to maximize ethanol production from the pretreated SCB by Scheffersomyces stipitis NRRL-Y7124, resulting in 31.50 g/L of ethanol, 0.49 g/g of ethanol yield and 0.68 g/L.h of productivity. All this showed that our HC-assisted NaOH-H2O2 pretreatment strategy along with the process intensification approach might offer an option for SCB-based biorefineries.

Hydrodynamic cavitation as a strategy to enhance the efficiency of lignocellulosic biomass pretreatment.

Hydrodynamic cavitation (HC) is a process technology with potential for application in different areas including environmental, food processing, and biofuels production. Although HC is an undesirable phenomenon for hydraulic equipment, the net energy released during this process is enough to accelerate certain chemical reactions. The application of cavitation energy to enhance the efficiency of lignocellulosic biomass pretreatment is an interesting strategy proposed for integration in biorefineries for the production of bio-based products. Moreover, the use of an HC-assisted process was demonstrated as an attractive alternative when compared to other conventional pretreatment technologies. This is not only due to high pretreatment efficiency resulting in high enzymatic digestibility of carbohydrate fraction, but also, by its high energy efficiency, simple configuration, and construction of systems, besides the possibility of using on the large scale. This paper gives an overview regarding HC technology and its potential for application on the pretreatment of lignocellulosic biomass. The parameters affecting this process and the perspectives for future developments in this area are also presented and discussed.

Sugarcane bagasse hydrolysate as a potential feedstock for red pigment production by Monascus ruber.

Sugarcane bagasse (SCB) hydrolysate could be an interesting source for red pigment production by Monascus ruber Tieghem IOC 2225. The influence of different wavelength of light-emitting diode (LED) at 250 µmol.m-2.s-1 of photon flux density on red pigment production by M. ruber in glucose-based medium was evaluated. Then, SCB hydrolysate was used as carbon source under the previously selected light incidence conditions. In glucose-based medium, the highest pigment production was achieved in fermentation assisted with orange LED light (8.28 UA490nm), white light (8.26 UA490nm) and under dark condition (7.45 UA490nm). By using SCB hydrolysate-based medium, the highest red pigment production (18.71 AU490nm) was achieved under dark condition and the glucose and cellobiose present in the hydrolysate were metabolized. SCB enzymatic hydrolysate was demonstrated to be a promising carbon source for high thermal stability red pigment production (activation energy of 10.5 kcal.mol-1), turning an interesting alternative for implementation in biorefineries.

Ethanol production in a simultaneous saccharification and fermentation process with interconnected reactors employing hydrodynamic cavitation-pretreated sugarcane bagasse as raw material.

In this study, sugarcane bagasse (SCB) pretreated with alkali assisted hydrodynamic cavitation (HC) was investigated for simultaneous saccharification and fermentation (SSF) process for bioethanol production in interconnected column reactors using immobilized Scheffersomyces stipitis NRRL-Y7124. Initially, HC was employed for the evaluation of the reagent used in alkaline pretreatment. Alkalis (NaOH, KOH, Na2CO3, Ca(OH)2) and NaOH recycled black liquor (successive batches) were used and their pretreatment effectiveness was assessed considering the solid composition and its enzymatic digestibility. In SSF process using NaOH-HC pretreatment SCB, 62.33% of total carbohydrate fractions were hydrolyzed and 17.26g/L of ethanol production (0.48g of ethanol/g of glucose and xylose consumed) was achieved. This proposed scheme of HC-assisted NaOH pretreatment together with our interconnected column reactors showed to be an interesting new approach for biorefineries.

Hydrodynamic cavitation as an efficient pretreatment method for lignocellulosic biomass: A parametric study.

Hydrodynamic cavitation (HC), which is a highly destructive force, was employed for pretreatment of sugarcane bagasse (SCB). The efficacy of HC was studied using response surface methodology (RSM) with determining parameters varied: inlet pressure of 1-3bar, temperature of 40-70°C, and alkaline concentration of 0.1-0.3M. At the best condition (3bar, 70°C and 0.3M NaOH), 93.05% and 94.45% of hydrolysis yield of cellulose and hemicellulose, respectively, were obtained within 30min of pretreatment time. Also, pretreatment time higher than 10min had little to do regarding to SCB composition changes using different orifice plates (16 and 27 holes, with corresponding cavitation number of 0.017 and 0.048, respectively), with higher hydrolysis yield observed at 20min of process. Therefore, HC-based approach could lead to a high yield of hydrolysis, as long as a treatment condition was right; it could be so at mild conditions and at short running time.

Low-melanin containing pullulan production from sugarcane bagasse hydrolysate by Aureobasidium pullulans in fermentations assisted by light-emitting diode.

Pullulan is a polymer produced by Aureobasidium pullulans and the main bottleneck for its industrial production is the presence of melanin pigment. In this study, light-emitting diodes (LEDs) of different wavelengths were used to assist the fermentation process aiming to produce low-melanin containing pullulan by wild strain of A. pullulans LB83 with different carbon sources. Under white light using glucose-based medium, 11.75g.L-1 of pullulan with high melanin content (45.70UA540nm.g-1) was obtained, this production improved in process assisted by blue LED light, that resulted in 15.77g.L-1 of pullulan with reduced content of melanin (4.46UA540nm.g-1). By using sugarcane bagasse (SCB) hydrolysate as carbon source, similar concentration of pullulan (about 20g.L-1) was achieved using white and blue LED lights, with lower melanin contents in last. Use of LED light was found as a promising approach to assist biotechnological process for low-melanin containing pullulan production.

Persulfate based pretreatment to enhance the enzymatic digestibility of rice straw.

Oxidation induced by potassium persulfate was evaluated as an economic substitute for the Fenton-like reaction for the purpose of rice straw pretreatment in terms of temperature (80-140°C), potassium persulfate concentration (5-100mM) and process time (0.5-3h), an optimal pretreatment condition was identified: 120°C for 2 h with 75mM potassium persulfate concentration and yielded 91% enzymatic digestibility using 25.2FPU/g of biomass. Crystallinity index, SEM and SEM-EDS analyses revealed that biomass was indeed disrupted and components like silica were exposed. All this suggested that this persulfate-based pretreatment method, which is distinctively advantageous in terms of effectiveness and economics, can indeed be a competitive option.

Hydrodynamic cavitation-assisted alkaline pretreatment as a new approach for sugarcane bagasse biorefineries.

Hydrodynamic cavitation (HC) was employed in order to improve the efficiency of alkaline pretreatment of sugarcane bagasse (SCB). Response surface methodology (RSM) was used to optimize pretreatment parameters: NaOH concentration (0.1-0.5M), solid/liquid ratio (S/L, 3-10%) and HC time (15-45min), in terms of glucan content, lignin removal and enzymatic digestibility. Under an optimal HC condition (0.48M of NaOH, 4.27% of S/L ratio and 44.48min), 52.1% of glucan content, 60.4% of lignin removal and 97.2% of enzymatic digestibility were achieved. Moreover, enzymatic hydrolysis of the pretreated SCB resulted in a yield 82% and 30% higher than the untreated and alkaline-treated controls, respectively. HC was found to be a potent and promising approach to pretreat lignocellulosic biomass.